Used Front Rear 2WD AWD Wheel Bearing Hub Assembly for Chevy Buick Cadillac

**NOTE: Please check fitment information before purchase, if you are not sure about the fit please feel free to contact us!**  **Kit Includes:** 1\* Front /Rear Wheel Hub and Bearing Assembly - 513121\*1 * * * **Caliper Specifications:** **Position:** Front or Rear **Lugs:** 5 Bolt **ABS Type:** Sensor Wire **Flange Type:** 3-Bolt Triangular * * * **Replaces OE Number:** **Chevy**: 12429204, 19235760 **Moog**: 513121, BR930548, HA590075 **General Motors**: 12413035, 7467357, 88964168 **OPEL**: 7470017, 7470568 **TRISCAN:** 853024113 * * * **Drivetrain types:** Front & 2WD( Front-Wheel Drive ) Front & 2WD( Front-Wheel Drive ) & 4 Wheel ABS Front & 2WD( Front-Wheel Drive/Rear-Wheel Drive ) Front & 2WD( Front-Wheel Drive )& EXC. heavy duty suspension Front or Rear & AWD( All-Wheel Drive ) Rear & AWD( All-Wheel Drive ) **FITMNET:** MAKE MODEL YEAR RANGE SPECIFIC DETAILS BUICK ALLURE 2005-2010 FRONT w/ FWD BUICK CENTURY 1997-2005 FRONT w/ FWD BUICK LACROSSE 2005-2009 FRONT w/ FWD BUICK LESABRE 2000-2005 FRONT w/ FWD BUICK LUCERNE 2006-2011 FRONT w/ FWD BUICK PARK AVENUE 1997-2005 FRONT, FWD BUICK REGAL 1997-2004 FRONT w/ FWD BUICK RENDEZVOUS 2002-2007 FRONT w/ FWD/ AWD BUICK RENDEZVOUS 2002-2006 REAR w/ AWD BUICK RIVIERA 1997-1999 FRONT w/ FWD BUICK TERRAZA 2005 FRONT w/ FWD FRONT OR REAR w/ AWD CADILLAC DEVILLE 1997-2005 FRONT w/ FWD CADILLAC DTS 2006-2011 FRONT, FWD; EXC. HEAVY DUTY SUSPENSION CADILLAC ELDORADO 1997-2002 FRONT w/ FWD CADILLAC SEVILLE 1997-2004 FRONT w/ FWD CHEVROLET IMPALA 2000-2013 FRONT w/ FWD; 4 Wheel ABS CHEVROLET MONTE CARLO 2000-2007 FRONT w/ FWD CHEVROLET UPLANDER 2005 FRONT w/ FWD FRONT OR REAR w/ AWD CHEVROLET VENTURE 2002-2004 FRONT OR REAR w/ AWD CHEVROLET VENTURE 1997-2005 FRONT w/ FWD OLDSMOBILE AURORA 1997-2003 FRONT w/ FWD OLDSMOBILE INTRIGUE 1998-2002 FRONT, FWD OLDSMOBILE SILHOUETTE 2002-2004 FRONT OR REAR w/ AWD OLDSMOBILE SILHOUETTE 1997-2004 FRONT w/ FWD PONTIAC AZTEK 2001-2005 FRONT w/ FWD FRONT OR REAR w/ AWD PONTIAC BONNEVILLE 2000-2005 FRONT w/ FWD PONTIAC GRAND PRIX 1997-2008 FRONT w/ FWD PONTIAC MONTANA 2001-2005 FRONT OR REAR w/ AWD PONTIAC MONTANA 1999-2005 FRONT w/ FWD PONTIAC TRANS SPORT 1997-1999 FRONT w/ FWD SATURN RELAY 2005 FRONT w/ FWD FRONT OR REAR w/ AWD * * * **Removal:** 1.Remove the bolt (1) and separate the front wheel sensor from the steering knuckle.? 2.Remove brake caliper torque member bolts, leaving brake hose attached, reposition the caliper aside with wire. 3.Put alignment marks (A) on disc brake rotor and wheel hub and bearing. Remove disc brake rotor. 4.Remove cotter pin and the nut retainer,Loosen the wheel hub lock nut from the drive shaft using power tool. 5.Using a piece of wood and a suitable tool, tap on the lock nut to disengage the drive shaft from the wheel hub and bearing. 6.Remove the engine side cover. 7.Remove the lower nut and bolt from the steering knuckle,Separate transverse link from steering knuckle. 8.Separate drive shaft from wheel hub and bearing, Reposition the drive shaft aside with wire. 9.Remove the wheel hub and bearing bolts using power tool. 10.Remove the splash guard and the wheel hub and bearing from the steering knuckle. **NOTE:** Failure to separate the front wheel sensor from the steering knuckle may result in damage to the front wheel sensor; Pull out the front wheel sensor, being careful to turn it as little as possible. Do not pull on wheel sensorharness. **Inspection after removel :** **Check components for deformationy,cracksy,and other damagey,and boots of transverse link ball joint for cracksy,axial end play,and swing torque.** * * * **Installation:** **Installation is in the reverse order of the removal.** **Caution:** 1.Do not reuse the wheel stud. 2.Do not reuse the cotter pin. 3.Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). 4.Clean the mating surfaces of the joint sub-assembly and the wheel hub and bearing. Apply lubricant to the surface (A) of the joint sub-assembly. 5.Hold the wheel hub and bearing using a suitable tool. Tighten the wheel hub lock nut 6.Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool. 7.Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification. 8.When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. 9.Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. * * * On Nov 4, 2025 at 01:22:13 PST, seller added the following information: * * * On Nov 18, 2025 at 00:16:22 PST, seller added the following information: 

• Bolt Circle Diameter: 4.528 Inches
• Car Model 1: Chevrolet Impala (2000-2013), Chevrolet Venture (1997-2005), Chevrolet Monte Carlo (2000-2007), Chevrolet Uplander (2005)
• Car Model 2: Buick Lacrosse (2005-2009), Buick Regal (1997-2004), Buick Rendezvous (2002-2007)
• Car Model 3: Cadillac Deville (1997-2005), Pontiac Grand Prix (1997-2008)
• Package Dimensions: 14.48 x 8.23 x 7.48 inches
• Compatible Lubricant: Grease
• Bearing Type: Roller Bearing
• Brand: Auto-Genie
• Type: Wheel Hub & Bearing Assembly
• Placement on Vehicle: Rear, Front, Right, Left
• Wheel Stud Quantity: 5
• Manufacturer Part Number: 513121
• Material: ‎Metal
• Flange Diameter: 5.728 Inches
• Item Weight: ‎18.06 pounds
• Interchange Part Number: Chevy: 12429204, 19235760, Moog: 513121, BR930548, HA590075, General Motors: 12413035, 7467357, 88964168, OPEL: 7470017, 7470568, TRISCAN: 853024113
• UPC: 756709197090